You are here: Home > Englander Pellet Stove Parts
Choose a sub category:
All Englander Pellet Stove Parts Find By Stove Model Find By Part Type

Englander Pellet Stove Parts

Englander Pellet StovesSummer's Heat Pellet StovesTimber Ridge Pellet Stoves


Englander pellet stoves are made by England’s Stove Works, which has been a family-owned and operated business since it was created over four decades ago. If you have an Englander and are in need of replacement or aftermarket Englander pellet stove parts, Pellet Stove Parts 4 Less is guaranteed to have what you need.


3/8" X 1 ¾" Hinge Pin Rivet for all Cast Door, by Englander AC-HP 3/8" X 1" Hinge Pin Rivet for all Cast Door, by Englander. AC-HP

Hinge Pin Rivet for cast stove door; 3/8" x 1 3/4". Please see technical specs for which stoves will fit the hinge pin rivet.

Price: $3.99
Control Board Fuse, by Englander PU-CBF Control Board Fuse (1 Fuse), by Englander PU-CBF

Fuse for Control Board. $4.99 for one fuse.
NOTE: Even If you have a stove that was supplied with a 5 amp, 120 Volt fuse, this can be used as a replacement.

Price: $4.99

(1)
DVD Service Video for Pellet Units (2002), by Englander PU-SCD DVD Service Video for Pellet Units (2002), by Englander PU-SCD

For pellet stoves produced before 2004...
(If you have a stove produced after 2004, see PU-DVD09)
Video (NOW on DVD) which covers a variety of pellet stove servicing procedures for Englander, Summers Heat and Timber Ridge models. Plays in your DVD player.

Price: $4.99
DVD Service Video for Pellet Units produced 2004 and later, PU-DVD09 Englander DVD Service Video for Pellet Units produced 2004 and later, PU-DVD09

For pellet stoves produced 2004 and later (Auto-Start Igniter stoves)...
(If your stove was produced before 2004, see PU-SCD)
DVD which covers a variety of pellet stove installation, maintenance and servicing procedures for Englander, Summers Heat and Timber Ridge models.

Price: $4.99
1/4” WIDE X 3” OD X 1” ID Rubber Gasket, by Englander CU-RG 1/4" WIDE X 3" OD X 1" ID Rubber Gasket, by Englander. CU-RG

Also known as a Rubber Vibration Dampener. This gasket can be seen on the diagram under #29. NOTE: Interchangeable with CU-RGN nylon gasket, both perform the same function.

Price: $5.99
Auger Bearing Gasket, by Englander PU-ABG Auger Bearing Gasket, for stoves built in 2000 or before by Englander PU-ABG

Auger Bearing Gasket. For stoves built in 2000 or before. Fits on block bearing (see Part Number PU-UCF204-12).

Price: $6.99
Auger Motor Support Sleeve, by Englander PU-AMS Auger Motor Support Sleeve, by Englander PU-AMS

Auger Motor Gasket Support Sleeve. Fits around outside air intake, Lower Auger Motor rests on it.

Price: $7.99

(1)
Brass Knob, by Englander AC-03 Brass Knob, by Englander. AC-03

Brass knob for ash drawer. Shown on ash drawer, also for cover of pellet insert (hopper) and gas cover plate.

Price: $8.99
Nickel Knob, by Englander AC-03BN Nickel Knob, by Englander. AC-03BN

Brushed Nickel knob for ash drawer. Shown on ash drawer, also for cover of pellet insert (hopper) and gas cover plate.

Price: $8.99
Burn Pot Gasket, by Englander PU-BPG Burn Pot Gasket, by Englander PU-BPG

Burn Pot Flange Gasket. Fits between the burn pot and the rear of the stove.

Price: $9.99

(3)
Spring Handle, by Englander AC-SH Gold Spring Handle, by Englander. AC-SH

Door spring handle (large). Color: Brass. Fits 1/2" diameter rod. Shown on 10-CPM, works on all stoves listed on this page.

Price: $9.99
Nickel Spring Handle, by Englander AC-SHN Nickel Spring Handle, by Englander. AC-SHN

Door Spring Handle (large). Color: Brushed Nickel. Fits 1/2" diameter rod. Shown on 49-SHCPML

Price: $9.99
Locking Collar, by Englander PU-2X570 Locking Collar, by Englander PU-2X570

3/4" I.D. Auger Shaft Locking Collar for pellet stoves. Price listed is for one piece (two pieces are on each stove, one per auger).

Price: $9.99
Auger Bearing Gasket, by Englander PU-ABGN Auger Bearing Gasket, for stoves built 2001 or later by Englander PU-ABGN

Auger Bearing Gasket. For stoves built 2001 or later. New material, replaces PU-ABG. Fits on block bearing (see Part Number PU-UCF204-12).

Price: $9.99

(1)
Slotted Cradle Gasket, by Englander PU-CGEP Slotted Cradle Gasket for stoves with IP in name, fits on cradle (under burn pot) by Englander PU-CGEP

Slotted Cradle Gasket for stoves with IP in name, fits on cradle (under burn pot) by Englander PU-CGEP

Price: $9.99
Glass Support Set for CA-EP Door, by Englander AC-GSEP Glass Support Set for CA-EP Door, by Englander. AC-GSEP

Replacement glass support set. See technical specs for a list of compatible stoves.

Price: $9.99
Combustion Motor to Housing Gasket for Englander Stoves, PU-CBMG-C Combustion Motor to Housing Gasket for Englander Stoves, 6" Round (N)

Circular shaped gasket. Combustion Blower Motor Gasket. Fits on Exhaust (Combustion) Blower motor, so that you can remove the motor from the Combustion Blower housing, clean your stove, and replace the motor and gasket without having to remove the entire Combustion Blower.

Price: $11.99

(2)
Englander Manual for 25-PDV & 55-SHP22, MU25PDV

Manual for Englander models 25PDV

Price: $11.99
Englander Manual, MU25PDVC

Englander manual for models 25-PDVC & 55SHP10

Price: $11.99
Combustion Housing to Stove Gasket for Englander Stoves, PU-CBMG-R Combustion Housing to Stove Gasket for Most Models (OS)(N)

Odd shaped gasket. Combustion Blower Gasket. Fits on Exhaust (Combustion) Blower flange, where blower meets stove.

Price: $12.99

(1)
Anderol 465 Synthetic Bearing Oil PP5400 Anderol 465 Synthetic Bearing Oil for Fasco motors and others. PP5400

This pellet stove bearing oil is rated for higher temperatures and will keep your bearings from prematurely wearing out due to heat and friction.

Price: $14.99

(3)
Englander Hopper Flange Gasket (3/8"),PU-HFG

Fits Models 25-PDV, 55-SHP22, 55-TRP22 check your manual to see if it fits your model

Price: $14.99
Combustion Blower Gasket and Motor Gasket, by Englander PU-CBMG Combustion Blower Gasket and Motor Gasket, by Englander PU-CBMG

Contains the following two items: 1. Combustion Blower Gasket. Fits on Exhaust (Combustion) Blower flange, where blower meets stove. The odd-shaped gasket pictured at top left. 2. Combustion Blower Motor Gasket. Fits on Exhaust (Combustion) Blower motor, so that you can remove the motor from the Combustion Blower housing, clean your stove, and replace the motor and gasket without having to remove the entire Combustion Blower. Replace the appropriate gasket each time you remove your motor (or entire blower assembly) to clean it.

Price: $17.99

(5)
Wear Plate for  PDV & PI for 2002 & Later Units, by Englander PU-BP98WPA Wear Plate fits all 25-PDV manufactured 2003 to present by Englander PU-BP98WPA

Wear Plate fits all 25-PDV manufactured 2003 to present. This is the plate that holds the pellets; it fits inside the burn pot of the stove.

Price: $19.99
Gasket Kit, by Englander AC-PGK Gasket Kit, by Englander. AC-PGK

Fireplace Cover Plate (backplate) gasket kit. **NOTE: For fireplace insert model only; not for Freestanding models.

Price: $19.99
Wear Plate for PDV & PI for 2002 & Later Units, by Englander PU-BP96WP Wear Plate for PDV & PI for 2002 & Later Units, by Englander PU-BP96WP

Wear Plate for all 1993 - 2000 Pellet Units (except 25-PDVC, 55-SHP10 or 55-TRP10 manufactured 1998-2003, see PU-BP98WP). This is the plate that holds the pellets; it fits inside the burn pot of the stove.

Price: $19.99
Englander Power Cord, AC-CORD

Fits most englander models: check your manual to confirm

Price: $19.99
Englander Black Spray Paint, AC-MBSP

High-temperature black spray paint. 12 oz. can.
NOTE: By law, this item can only be shipped UPS Ground (even if you phone in your order), no express available.
Two cans of paint should paint your entire unit.
Older Units: Replaces AC-MCSP (charcoal gray) spray paint if you have an older stove.
(Not for powder-coated gas units; order AC-PCBSP if you have a powder-coated gas unit.)

Price: $19.99
Englander Exhaust Tube Gasket Insulation, PU-PGB52

Insulation Exhaust Tube Gasket.wraps around Exhaust Tube of stove. Fits Englander Models:
25-PDV, 55-SHP22, 55-TRP22...fits more models check your manuals before ordering for part number

Price: $19.99
Auger Coupler, by Englander CA-AC Auger Coupler, by Englander. CA-AC

Replacement auger coupler for corn stoves. See technical specs for a list of compatible stoves.

Price: $22.99
Magnet for IP, by Englander AC-MAG Magnet for IP, by Englander. AC-MAG

Magnet for door. One in a package. Please see technical specs for a list of compatible stoves for this part.

Price: $22.99
Pellet Stove Wear Plate PU-BP98WP

Wear Plate fits all 25-PDVC from 1998 through the present date also is used on 25-PDV built in 2001 or 2002 and all 25-PAF manufactured 1998 or later. This is the plate that holds the pellets; it fits inside the burn pot of the stove.

Price: $24.99
Englander Hopper Lid Latch, PU-103-50

Hopper Lid Latch. One per package.
NOTE: As a TOP LID latch, was for pellet stoves manufactured 2001 and
earlier. For pellet stoves manufactured 2002 or later, see Part Number
PU-62-40-151-3.
However, is used later on some models as an ash pan latch, for example.
See your stove's parts diagram in your owner's manual.

Price: $24.99
Auger Bearing, by Englander PU-UCF204-12 After Market Auger Bearing For Englander PU-UCF204-12 (AMP20089)

Auger Bearing (block bearing) for pellet units. 3/4" bore. Price listed is for one piece (two pieces are on each stove, one per auger).

Price: $24.99
Glass Gasket (and/or Ash Pan Gasket) Kit, By Englander AC-GGK Glass Gasket (and/or Ash Pan Gasket) Kit, By Englander. AC-GGK

Window glass gasket kit. Includes gasket (approx. 1" x 7' flat, adhesive on one side). Does not include glass. Includes self-adhesive backing for easy strip and press application. Is also used as Ash Pan gasket on some stoves, see your stove's parts diagram or owner's manual for reference. If ordering for glass gasket and ash pan gasket, you should order two kits.

Price: $29.99

(1)
Door Gasket Kit, by Englander AC-DGKC Door Gasket Kit, by Englander. AC-DGKC

Door Gasket Kit for models manufactured after July 1988. (Note: Also for wood insert models with JC or 20 in model number with manufacture date of 1986-1995). 3/4" round door gasket, includes silicone necessary to install.

Price: $29.99

(2)
Vacuum Hose for Vacuum Switch, by Englander PU-VS Vacuum Hose for Vacuum Switch, by Englander PU-VH

Vacuum Hose Kit for vacuum shut-down switch. Contains one 21-inch piece
and two 12-inch pieces. This should fit whatever model you have.

Price: $29.99

(1)
Auger Bearing, by Englander PU-UCF204-12 Auger Bearing, by Englander PU-UCF204-12

Auger Bearing (block bearing) for pellet units. 3/4" bore. Price listed is for one piece (two pieces are on each stove, one per auger).

Price: $29.99
Door Gasket Kit, by Englander AC-DGKNC Door Gasket Kit, by Englander. AC-DGKNC

Door gasket kit (for models listed on this page). Includes silicone necessary to install; 5/8" round gasket. Include your model number and manufacture date in the "Ordering Instructions" box when you check out.

Price: $29.99

(1)
Hopper Lid Gasket, by Englander PU-HLG Hopper Lid Gasket, by Englander PU-HLG

Comes with proprietary instructions for installing on our units. NOTE: Does NOT turn pellet stove On & Off, it does increase or decrease the pellet feed rate as needed. EXCEPTION: For our multi-fuel model and our pellet models with "EP," "IP" or "PAH" in model number, will turn entire unit on & off as needed OR use a "High/Low" mode of operation

Price: $29.99

(1)
Door Gasket Kit for EP, by Englander AC-DGKEP Door Gasket Kit for EP, by Englander. AC-DGKEP

Door Gasket Kit for "Evolution Pellet" models listed on this page. 3/4" round door gasket, includes silicone necessary to install.

Price: $29.99
Ash Pan Gasket, by Englander AC-APG Ash Pan Gasket, by Englander. AC-APG

This is a replacement ash pan gasket. See technical specs for a list of compatible stoves.

Price: $29.99
Vacuum Shut-Down Switch, by Englander PU-VS After Market Englander Vacuum Switch, PU-VS(AMP20091)

After Market Version of the Englander Vacuum Shut Down Switch. The vacuum hose from this switch connects to the Exhaust Blower of the stove. Will retro-fit to older (metal) type switches in our older model pellet units. 2006 and later model pellet stoves use 1 ea CU-VS and 1 ea PU-VS. Pre 2006 models use 2 ea PU-VS.

Price: $29.99
Hopper Lid Safety Switch Button Type, by Englander AC-HLSB Hopper Lid Safety Switch Button Type, by Englander. AC-HLSB

Hopper Lid Safety Switch. Sometimes listed as AC-HLS or PU-HLS.
Important! You must replace with the type of switch that came with your stove...If your switch is a "arm" type rather than this, see AC-HLSA.

Price: $34.99
Hopper Lid Safety Switch Arm Lever, by Englander AC-HLSA Hopper Lid Safety Switch Arm Lever, by Englander. AC-HLSA

Hopper Lid Safety Switch. Sometimes listed as AC-HLS or PU-HLS.
Important! You must replace with the type of switch that came with your stove...If your switch is a "button" type rather than this, see AC-HLSB.

Price: $34.99
Englander Recessed Hopper Lid Latch, for all pellet units manufactured 2002 and later. PU-62-40-151-3

Recessed Hopper Lid Latch.For all pellet units manufactured 2002 and later. For units manufactured prior to 2002, see Part Number PU-103-50. (NOTE: Also for pellet grill/smokers with PG100 in model number)

Price: $34.99
Vacuum Shut-Down Switch, by Englander CU-VS After Market Vacuum Shut-Down Switch for Englander CU-VS(AMP20092)

After Market Version of the Englander Vacuum Shut Down Switch. This is the "Door Ajar Switch." The vacuum hose from this switch connects directly to the firebox of the stove. This part is used in 2006 and later model pellet stoves.

Price: $34.99
Vacuum Shut-Down Switch, by Englander PU-VS Englander Vacuum Switch, PU-VS

Englander Vacuum Shut Down Switch. The vacuum hose from this switch connects to the Exhaust Blower of the stove. Will retro-fit to older (metal) type switches in our older model pellet units. 2006 and later model pellet stoves use 1 ea CU-VS and 1 ea PU-VS. Pre 2006 models use 2 ea PU-VS.

Price: $39.99
Heat Sensor For Control Board, by Englander PU-CBHS Heat Sensor For Control Baord, by Englander PU-CBHS

Heat Sensor for Control Board (the white-covered wire shown in photo). For PU-CB98 or PU-CB04 control boards (used on all pellet stoves manufactured 1998 or later).

Price: $39.99

(3)
Auger Mounting Plate, by Englander CA-AMPP Auger Mounting Plate, by Englander CA-AMPP

Replacement mounting plate for auger motor. See technical specs for a list of compatible stoves.

CA-AMPP has two set screw holes along with recesses for each screw to mount it to the motor.

CA-AMP
only has the place for the screws and 1 set screw to hold it on.

Price: $39.99
Bottom Auger, by Englander PU-AF12B Bottom Auger Shaft For models made between 1992-2000, by Englander PU-AF12B

Bottom Auger. For 1992-2000 models. For models 2001 and later, order PU-AF11B.

Price: $44.99
Auger for 10-CDV, by Englander CU-AFC Auger for 10-CDV, by Englander. CU-AFC

Auger for Corn Stove. Please see technical specs for a list of compatible stoves.

Price: $44.99
Ash Pan for PAH, by Englander. PAH-AP

Ash Pan for Pellet Auxiliary Heater models

Price: $48.99
Vacuum Shut-Down Switch, by Englander CU-VS Vacuum Shut-Down Switch, by Englander CU-VS

Englander Vacuum Shut Down Switch. This is the "Door Ajar Switch." The vacuum hose from this switch connects directly to the firebox of the stove. This part is used in 2006 and later model pellet stoves.

Price: $49.99

(1)
Bottom Auger, by Englander PU-AF11B Bottom Auger Shaft, by Englander PU-AF11B

Bottom Auger. For all 25-PDVC/55-SHP10/55-TRP10 units. Also for ALL pellet models 2001 and later. NOTE: For models 1992-2000, and other than 25-PDVC, 55-SHP10 or 55-TRP10 order Part Number PU-AF12B. NOTE: Does not include Locking Collar (PU-2X570) or Block Bearing (PU-UCF204-12).

Price: $49.99
Auger for 25-EP/PUF/PAH, by Englander PU-AFEP Auger for all "Evolution Pellet" by Englander PU-AFEP

Steel Auger for all "Evolution Pellet" (Freestanding and Insert models with EP in model number), Pellet Utility Furnace and Pellet Auxiliary Heater Stove models listed on this page. Also for "Imperial Pellet" units (IP in model number).


Price: $49.99
Insert Hinge for EP Insert Kit, by Englander PU-IH Insert Hinge for EP Insert Kit, by Englander PU-IH

Recessed Hopper Lid Hinge. One per package. This is the hinge for the hopper lid for all pellet insert models listed on this page. Two per stove, price shown is for one hinge.

Price: $49.99
Outside Air Kit for Pellet Units, by Englander PU-OAK Outside Air Kit for Pellet Units, by Englander PU-OAK

This kit is manufactured by England's Stove Works. Provides outside air
that is mandatory for most pellet and multi-fuel installations
(including all England's Stove Works models).

Price: $59.99
Upgrade Baffle for PDV-PI 2001 or later, by Englander PU-5206-10 Upgrade Baffle for 25PDV & 25PI 2001 to present day, by Englander PU-5206-10

Impingement (baffle) Plate for 25-PDV, 55-SHP22 and 55-SHP22L, 55-TRP22 or American Heritage pellet stoves (or 25-PI, 55-SHP20 or 55-TRP20 pellet insert) manufactured 2001 and later. For models manufactured before 2001, see IP-25PDV2 and IP-25PDV3.
Plate(s) may or may not be exactly like plate pictured here (this is to give a general idea of appearance of part).
Please be sure to list model number and mfg. date in the Ordering Instructions box when you check out.

Price: $59.99
Brass Trim for 9.25 x 16.5 Glass CA-13, by Englander AC-108 Brass Trim for 9.25 x 16.5 Glass CA-13, by Englander. AC-108

Brass trim. Fits doors with 9.25" x 16.5" glass. Shown on 13-NCL, works with any stove on this page except stoves with gold-plated doors.
Does not include two-piece lip trim; see AC-107 for lip trim.
Note: Lip trim is not available for Pellet Auxiliary Heater (stoves with "PAH" in model number).

Price: $59.99
Nickel Trim for 9.25 x 16.5 Glass, by Englander AC-108BN Nickel Trim for 9.25 x 16.5 Glass, by Englander. AC-108BN

Brushed Nickel trim. Fits doors with 9.25" x 16.5" glass. Shown on 50-SNC13PL, works with any stove on this page except stoves with gold-plated doors.
Does not include two-piece lip trim; see AC-107BN for lip trim.
Note: Lip trim is not available for Pellet Auxiliary Heater (stoves with "PAH" in model number).
[Add to Cart]  [View Cart]

Price: $59.99
Kwik Fire After market replacement Igniter for Englander pellet stoves (PP3515). Replaces item PU-CHA. After market replacement Igniter for Englander pellet stoves. Replaces item PU-CHA. PP3515

Kwik Fire After market replacement igniter for Englander pellet stoves. Replaces item PU-CHA. 1 Year limited warranty.
Englander: Summer Heat & Summers Heat. Most Models 2004-present

We also offer a full line of Englander pellet stove parts.

Price: $69.99

(1)
After Market Firebrick (PP1022) Fits Englander Stoves Replaces #CPM-CFB Englander Pellet Stoves After Market Firebrick Replaces part #CPM-CFB, PP1022

This is an After Market Firebrick. *****Replaces part #CPM-CFB

Price: $69.99
After Market Firebrick (PP1023) Fits Englander Stoves Replaces #AC-CFBEP Englander Stoves After Market Firebrick Replaces part #AC-CFBEP. #PP1023

This is an After Market Firebrick. For Englander part #AC-CFBEP

Price: $69.99
Igniter for Multi-Fuel, by Englander PU-CH6 After Market Version of the Englander Multi-Fuel Stove Igniter, PU-CH6 (AMP20096K)

Cartridge Heater element for our 10-CPM/49-SHCPM/49-TRCPM multi-fuel stoves.
NOTE: There is an old assembly number CPM-CH.

Price: $69.99
Digital Wall Thermostat, by Honeywell PU-DTSTAT Digital Wall Thermostat, by Honeywell For use with Englander stoves and others. PU-DTSTAT

Digital Wall Thermostat. Can be used on all Englander pellet units, as well their multi-fuel unit.
Mercury-Free!

Price: $79.99
Glass Kit, by Englander AC-G3 Glass Kit, by Englander. AC-G3

Glass Kit for 28-IC, 28-JC, 18-PC, 24-AC and 24-FC (FC models prior to 1997 only). Comes with gasket pre-mounted on glass.
Englander Wood Stove:, 24-FC, 50-SHW16, 50-SHW16L, 50-TRW24, 50-TRW16

Price: $89.99
Ash Pan for EP Stoves, by Englander PU-APEP Ash Pan for EP "Evolution Pellet" Stoves, by Englander PU-APEP

Ash Pan for "Evolution Pellet" models listed on this page.

Price: $89.99
Brick Fiber Board, by Englander. AC-CFBEP

Ceramic Fiber Board for "Evolution Pellet" Stove models.

Price: $99.99
Cartridge Heater, by Englander PU-CHA Englander Igniter Cartridge Heater(For Auto-Start units with a manufacture date of 2004 or later) PU-CHA

This is the element that fits inside the Auto-Igniter element
tube...this element fits the bolt-on tube (stoves manufactured before
August 2004) as well as the built-in cast tube (stoves manufacutured
after August 1, 2004).

Price: $99.99

(2)
Log Set, by Englander AC-LSEP Log Set, by Englander. AC-LSEP

This log set is a replacement for the following Englander Stoves:
25-EP
55-SHPEP
55-SHPEPL
55-TRPEP
25-EPI
55-SHPEPI
55-SHPEPIL
5-TRPEPI

Price: $99.99
Firebrick Kit, by Englander CPM-CFB Firebrick Kit, by Englander. CPM-CFB

This firebrick kit will work for the following for Multi-fuel Stoves:
- 10-CPM, 49-SHCPM, 49-TRCPM
- 25-IP, 25-IPM, 25-IPS, 55-SHPIP, 55-SHPIPL, 55-SHPIPM, 55-SHPIPS and 55-TRPIP, 55-TRPIPM and 55-TRPIPS Parts

Price: $99.99
Igniter for Multi-Fuel, by Englander PU-CH6 Englander Multi-Fuel Stove Igniter PU-CH6

Cartridge Heater element for our 10-CPM/49-SHCPM/49-TRCPM multi-fuel stoves.
NOTE: There is an old assembly number CPM-CH.

Price: $99.99
Burn Pot for 10-CDV, by Englander CU-BP Burn Pot for 10-CDV, by Englander. CU-BP

Burn Pot for Corn Stove (models that begin with 10-CDV, 49-SHC22 and 49-TRC22)

Price: $99.99
Burn Pot for 10-CPM Stove, by Englander CPM-BP Burn Pot for 10-CPM Stove, by Englander. CPM-BP

Burn Pot for 10-CPM Stove

Price: $99.99

(1)
Burnpot for 25-PAH & 55-TRPAH, PAH-BP Englander Burnpot. PAH-BP

This burnpot fits the following stoves: 25-PAH, 55-TRPAH

Price: $99.99

(1)
After Market Auger Feed Motor 2 RPM CW (PP7002), Replacement for Englander CU-047042 and St.Croix #80P20278-R After Market Auger Feed Motor 2 RPM CW, Replacement for Englander and St.Croix PP7002

THIS IS AN AFTER MARKET AUGER MOTOR 2 RPM CW MAXI-TORQ™
Premium Heavy Duty Auger Motor.

Turns Clockwise.

Price: $109.99
Fuel Stirrer for Corn Stove, by Englander CA-FS Fuel Stirrer for Corn Stove, by Englander CA-FS

Fuel Stirrer (stainless) for Corn Stove (models that begin with 10-CDV, 49-SHC22 and 49-TRC22). Please see technical specs for a list of compatible stoves.

Price: $109.99
Englander Nickel Louver, AC-114BN

55-SHP22L; works on 25-PDV, 55-SHP22, 55-TRP22 (freestanding deluxe pellet) and 25-PI, 55-SHP20 and 55-TRP20 (pellet insert)manufactured 2001 and later.

Price: $109.99
Englander door glass and gasket kit Englander Door Glass Kit AC-G9

Door Glass Kit. Includes 9 1/8" x 9 1/8" glass, and gasket necessary to install.

Price: $119.99
Brass Backplate Trim for 25-EPI, by Englander AC-121 Brass Backplate Trim for 25-EPI, by Englander. AC-121

Brass Backplate Trim (fits standard-size coverplate supplied with unit). Fits around top & sides of coverplate; 3-piece set, clips for installation are included.
NOTE: Shown on 25-EPI, works on all fireplace insert stoves listed on this page.
NOTE: For fireplace insert ONLY, not for freestanding (leg, cabinet or pedestal) units

Price: $119.99
Fuel Stirrer for Multi Fuel Stove, by Englander CPM-FS Fuel Stirrer for Multi Fuel Stove, by Englander CPM-FS

Fuel Stirrer for Multi Fuel Stove for the following stoves:
- 10-CPM, 49-SHCPM, 49-TRCPM (models with 'CPM' in model number)

Price: $119.99
After Market Auger Motor (PP7100), replacement for Englander PU-047040 After Market Auger Motor 1 RPM Counter Clockwise Fits Englander & Others, AMP20131

This is a replacement for Englander part PU-047040. Also fits Quadrafire US Stove & Vogelzang. Click here to check compatibility.

Price: $119.99

(1)
Center Glass, 10.5” x 14.25”, by Englander AC-G40 Center Glass, 10.5 x 14.25 by Englander. AC-G40

Door Glass. Includes 10.675" x 14.438" glass, and gasket necessary to install. Shown on 25-EP as center glass, works on all models listed on this page.

Price: $129.99
Burn Pot for EP, by Englander PU-BPEP Burn Pot for EP models, by Englander PU-BPEP

Burn Pot unit for "Evolution Pellet" (models with EP in model number) and "Imperial Pellet" (models with IP in model number) stove models listed on this page. This is a one-piece unit, and is the actual burn pot (does not include the "cradle" - see picture).

Price: $129.99

(1)
Englander Cartridge Heater Assembly, AC-CHSEP-TSC

Cartidge heater assembly.
Comes with:
PU-CHA - Ignitor
AC-CHSEP ( Ignitor tube and positioning collar with tab)

Price: $129.99
Glass 9.25 x 16.5 for 12's and 13's , by Englander AC-G17 Glass 9.25 x 16.5 for 12's and 13's , by Englander. AC-G17

Door Glass Kit. Includes 9 1/4" x 16 1/2" glass, and gasket necessary to install. Shown on wood stove, fits all models listed on technical specs tab.

Price: $139.99
Combustion blower for Enviro and Breckwell stoves After market Combustion blower for Englander, Enviro & Breckwell, AMP20049

This is an after market combustion blower that is compatible with all Englander stoves using the PU-076002B also Enviro and Breckwell pellet stoves. The Combustion Blower is designed to pull combustion air through the stove and push it out through the vent piping. ***EF-161 AND EF-161A ARE THE SAME PART**** This Combustion Blower is used on all Breckwell pellet stoves except the P28.***THIS REPLACES A-E-027 WITH OUT THE HOUSING, IF YOU NEED THE HOUSING GET AFTER MARKET PART PP7692***

Price: $139.99

(1)
Auger Motor, by Englander PU-047040 1 RPM Counter Clockwise Auger Motor, by Englander PU-047040

This auger motor will fit on the following England Stove Works stoves:
25-PDVC, 55-SHP10 and 55-SHP10L, American Standard and 55-TRP10  
25-PDV, 25-PDVP, 55-SHP15, 55-SHP22 and 55-SHP22L, 55-TRP15, 55-TRP22, American Heritage and US 25-5670  
25-PAF, 55-SHP25 and 55-TRP25  
25-PI, 55-SHP20 and 55-TRP20  
10-CPM, 49-SHCPM, 49-TRCPM

Price: $149.99

(3)
Brushed Nickel Window Trim for EP Stoves, by Englander AC-120-BN Brushed Nickel Window Trim for EP Stoves, by Englander. AC-120-BN

Nickel Window Trim. This is actually a 15-piece kit that will provide trim for all 3 windows; very good quality, instructions included.
Note: For Nickel door handle, see AC-SHN.
Note: Shown on 25-EP, works on the technical specs tab.

Price: $149.99
Englander Brass Louver, AC-114

25-PDV, works on 25-PDV, 55-SHP22, 55-TRP22 (freestanding deluxe pellet) and 25-PI, 55-SHP20 and 55-TRP20 (pellet insert)manufactured 2001 and later.

Price: $149.99
Brass Window Trim for EP Stoves, by Englander AC-120 Brass Window Trim for EP Stoves, by Englander. AC-120

Brass Window Trim. This is actually a 15-piece kit that will provide trim for all 3 windows; very good quality, instructions included.  Note: Shown on 25-EP, works on any stove listed on this page.

Price: $159.99
Englander Pellet Stove Complete GASKET KIT; Save Over $25.00!


Comes with all of the essential gaskets needed for your pellet stove. Includes AC-DGKC Door Gasket (includes silicone necessary to install); AC-GGK Window Gasket; PU-HLG Hopper Lid Gasket; PU-CBMG Combustion Blower Gaskets; PU-ABGN Auger Bearing Gaskets (set of 2); AC-APG, Ash Pan Gasket & PU-BPG Burn Pot Gasket

Price: $189.99
Sale Price: $159.99
You save $30.00!
Auger Motor, by Englander CU-047042 Englander Auger Motor 2.4 RPM For Multi Fuel and certain pellet stoves# CU-047042

2.4 rpm auger ('feed') motor for our Multi-Fuel unit

This auger motor will fit on the following England Stove Works stoves:
25-EPI, 55-SHPEPI, 55-SHPEPIL and 55-TRPEPI 10-CDV  
10-CDVP, 10-CDVL &10-CDVG; 49-SHC22P, 49-SHC22L & 49-SHC22G; 49-TRC22P, 49-TRC22L & 49-TRC22G  
25-IP, 25-IPM, 25-IPS, 55-SHPIP, 55-SHPIPL, 55-SHPIPM, 55-SHPIPS and 55-TRPIP, 55-TRPIPM and 55-TRPIPS  
10-CPM, 49-SHCPM, 49-TRCPM
25-PUF, 55-SHP240 and 55-TRP240
25-EP, 55-SHPEP, 55-SHPEPL and 55-TRPEP
25-PAH, 55-SHPAH, 55-SHPAHL and 55-TRPAH

Price: $169.99
englander pellet stove blower motor Englander Pellet Stove Convection Blower PU-4C442

IMPORTANT: For all pellet models listed on this page except 2002 and newer "Deluxe" freestanding and insert pellet models ("Deluxe" models have louvers beside the door and include model numbers models 25-PDV, 25-PI, 55-SHP22, 55-SHP20, 55-TRP22, 55-TRP20, 55-SHP22L and American Heritage models).
If 2002 or newer "Deluxe" model, see Part Number PU-4C447 Convection Blower. **NOTE on Older Models: Model years 1989-90 use one room air blower; Model years 1991-95 use two room air blowers. (If 1991-95 model, stand behind the stove and determine if "left" or "right" blower, and note this in the "Ordering Instructions" box in your Shopping Cart.) Model years 1996 and later use one room air blower. For a list of models that are compatiable, please click on the Extended Features tab.

Price: $189.99

(1)
Convection / Room Air Blower For Deluxe Models, by Englander PU-4C447

Convection (Room Air) Blower. 250 cfm. **NOTE: For all models listed on this page - Corn/Multifuel Stoves, Pellet Utility Furnace, Pellet Auxiliary Heater and 2002 and later "Deluxe" freestanding and insert pellet models. NOTE: For "Deluxe" models made before 2002, see PU-4C442 Convection Blower ("Deluxe" models have louvers: 25-PDV and 25-PI, 55-SHP22, 55-SHP22L and 55-SHP20, 55-TRP22 and 55-TRP20, American Heritage).

Price: $199.99

(2)
Combustion Exhaust Blower by Englander PU-076002B Englander Combustion (Exhaust) Blower, Fits most Englander Pellet Stove models PU-076002B

Our pellet stove exhaust blower comes with the complete assembly with gasket and pipe adaptor, and mounts securely in place of your existing blower. This blower comes with everything you need for installation including wire leads that make installation a breeze.

Price: $199.99

(3)
Burn Pot Cradle for EP, by Englander PU-BPCEP Burn Pot Cradle for EP stoves, by Englander PU-BPCEP

Burn Pot Cradle for "Evolution Pellet" Stove models listed on this page. This is a one-piece unit, and is the "cradle" that houses the burn pot; it does not include the burn pot (see picture).

Price: $199.99
Burn Pot for PDVC & PAF, by Englander PU-BP02 Burn Pot for PDVC & PAF, by Englander PU-BP02

Burn Pot (firepot) Assembly. This is a one-piece unit, which is the burn pot only (not the entire "feeder system") for the pellet stove. This is a welded assembly. For 25-PDVC, 55-SHP10, 55-SHP10L, 55-TRP10 and American Standard manufactured from 1998 to present. Also for 25-PAF, 55-SHP25 and 55-TRP25 manufactured from 2002 to present. See technical specs to see all the compatible stoves.

Price: $199.99
Englander Burn Pot, PU-BP02A Englander Burn Pot For 25-PDV and others manufactured from 1998 to present., PU-BP02A

Burn Pot (firepot) Assembly. This is a one-piece unit, which is the burn pot only (not the "feeder pot") for the pellet stove. This is a welded assembly. For 25-PDV, 55-SHP22, 55-SHP22L, 55-TRP22 and American Heritage manufactured from 1998 to present. Also for 25-PI, 55-SHP20 and 55-TRP20 manufactured from 2002 to present.

Price: $199.99
Digital Control Board, by Englander PU-CB04 Digital Control Board by Englander,For models manufactured 2004 or later (auto-start igniter models). PU-CB04

Digital System Control Board (rear of board is pictured). For models manufactured 2004 or later (auto-start igniter models). (For models manufactured before 2004 [without auto-start igniter], see PU-CB98.) Does not work with stove model 25-PAH

Price: $299.99
Digital Control Board, by Englander PU-CB98 Digital Control Board For models manufactured EARLIER THAN 2004 (Special Order see description for details, by Englander PU-CB98

YOU
MUST INCLUDE YOUR MODEL,SERIAL NUMBER, AND DATE OF MANUFACTURER IN THE
ORDER NOTES SECTION AT CHECKOUT. THIS CONTROL BOARD MUST BE PROGRAMMED
AT THE FACTORY BEFORE SHIPMENT.

Price: $299.99
Digital Control Board for EP models, by Englander PU-CBEP

Digital Control Board for Englander stove models: 25-EP, 55-SHPEP, 55-SHPEPL, 55-TRPEP, 25-EPI, 55-SHEPI, 55-SHPEPIL, 55-TRPEPI

READ BEFORE ORDERING:

When placing an order for this control board, please include the following in your order notes:
-Make
-Model
-Serial Number
-Date of Manufacture

We must have ALL of this information for your stove before we can ship out your order. Please note, there is NO EXPRESS SHIPPING offered for this item.

Price: $299.99
Englander Digital Control Board Fits 25-PUF only. # PU-CB240-06

Englander Digital Control Board Fits 25-PUF only. # PU-CB240-06

Price: $299.99
Englander Control Board, PAH-CB09

Digital Control Board for the Englander 25-pah/ 55shpah/ 55trpah only

Price: $299.99

Parts for Every Englander Component

Englander pellet stove parts are designed to provide one of the most reliable heating systems on the market, saving you money on heating costs during the harsh winter months. We have everything you’ll need to repair, replace, clean and maintain your Englander pellet stove with the expertise to help you find what you need before you buy.

Keeping your Englander pellet stove parts in top working condition will save you money by helping heat your entire home or provide an affordable supplement to your current heating system.

Pellet Stove Parts 4 Less carries parts for every element on your Englander stove, from the motor to the power to the paint to the switches and sensors. Our full line of Englander pellet stove parts includes but isn't limited to, things like:

  • Service videos and manuals
  • Gaskets and flanges
  • Motors and bearing oil
  • Knobs and handles in both nickel and brass options
  • Wear plates and lids
  • Power cords
  • Stove paint
  • Vacuum switches
  • Heat sensors
  • Igniters
  • Firebrick
  • Control boards and fuses

We also offer free shipping on orders over $49, so you can get all the parts you need for your stove at the lowest possible price, and you don’t have to worry about shipping and handling fees on top of it all.

More About Englander Pellet Stoves

Englanders can heat spaces as large as 2,200 square feet, and most of them are designed for overnight burns at least. Englander stoves are among the best selling pellet stoves ever, and this is thanks to their economical price, their efficiency, and their versatility (they can even be installed in mobile homes). And to meet the demand for alternative energy, England’s Stove Works even makes a multi-fuel pellet stove that can run on pellets, corn, and cherry pits.