Skip to main content
Skip to main content
Product title:

Enviro Igniter for Pre-2004 Pellet Stoves: EF-127

Product rating:
Product price:
$249.99
Product SKU ! EF-127
Product MPN ! EF-127
Bullet point features

Description

Genuine Enviro Replacement 115V Pin Ignitor for Select Enviro Pellet Stoves Made Prior to 2004, See Compatible. 

 NOTE:

Length from flange to end of ignitor tube going into burn out area: 2-9/16"


Replacement For Part Number:

  • EF-127

View Compatible Models

UPC: 200001155109

Compatible Models

    Enviro

  • EF2 FS
  • EF3
  • EF4 FS

Technical Specs

Volts 115V
Length 6-1/2"
Connectors Halogen Pin Connectors

Videos

Instructions

Install Instructions For Enviro Igniter for Pre-2004 Pellet Stoves: EF-127

This igniter plugs into to a socket, known as the halogen pin socket. The pins from this part most likely will not self align. Prior to removing the the igniter the intake box located under the auger motor must be removed and the halogen pin socket leads need to be free from the wire harness so that when the igniter is removed, the halogen socket travels with the igniter through the front of the stove so it can be plugged in. Either pin may attach into either hole. Reinstall the igniter and then take up the wire slack in the back to prevent the socket pin wires from touching the exposed igniter tube.

Troubleshooting

****This igniter ONLY exists is Enviro and Vista Flame stoves and inserts made PRIOR to 2004****


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Information

This Item Qualifies For Free Shipping!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information
Jump back to product information tab navigation

Description

Genuine Enviro Replacement 115V Pin Ignitor for Select Enviro Pellet Stoves Made Prior to 2004, See Compatible. 

 NOTE:

Length from flange to end of ignitor tube going into burn out area: 2-9/16"


Replacement For Part Number:

  • EF-127

View Compatible Models

UPC: 200001155109

Technical Specs

Volts 115V
Length 6-1/2"
Connectors Halogen Pin Connectors

Instructions

Assembly Instructions For Enviro Igniter for Pre-2004 Pellet Stoves: EF-127

This igniter plugs into to a socket, known as the halogen pin socket. The pins from this part most likely will not self align. Prior to removing the the igniter the intake box located under the auger motor must be removed and the halogen pin socket leads need to be free from the wire harness so that when the igniter is removed, the halogen socket travels with the igniter through the front of the stove so it can be plugged in. Either pin may attach into either hole. Reinstall the igniter and then take up the wire slack in the back to prevent the socket pin wires from touching the exposed igniter tube.

Troubleshooting

****This igniter ONLY exists is Enviro and Vista Flame stoves and inserts made PRIOR to 2004****


It is advisable to ALWAYS replace your door gasket when you are replacing an igniter. A leaking door gasket is often a contributing factor to igniter failure.

Troubleshooting Igniters:

Igniter failure can be verified on one of three ways. The easiest and most common way to see if the igniter is working is to start your stove or grill and visually look for the orange glow; however, some appliances do not have a visual way to do this, so you may have to physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated. If you can see the glow or can feel the heat from the igniter, chances are that the igniter is actually working. If this is the case, retry the startup process. Make sure your burn pot is seated correctly if it is removable. Make sure that your ash pan, door or hopper lid is closed as this will provide an airtight seal on the stove, which most igniters will require for proper ignition. If you still do not have any luck, give the stove a good cleaning, including the vent, and try again. If these attempts fail, further troubleshooting will be required, which leads us to the third method.

For this method, you will need a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. While you are taking the igniter out, verify that it is installed correctly with the correct mounting equipment, screws, etc.. With the igniter removed from the stove, you will need to look over the part to find the rated watts, it’s usually stamped on the metal somewhere. If you cannot find it, look on our website for the correct igniter; the information you are looking for will be under “technical specs”

If your Ohms reading is within 10%, more or less than the rating (46Ω +/- 10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. An example of this would be your stove requires a 300W igniter but the stove has a 250W igniter installed. The reading in this scenario would be 52Ω. The reading would be correct to the igniter but would be the wrong value for the specified 300W igniter. That’s why it’s usually good to look at the part itself for the watts rating.

Warranty

Unfortunately, sometimes products do not work like they are supposed to. We offer a 90 day warranty on manufacturer defects. Some manufacturers make this a very simple and easy process unfortunately others do not. Items must be used in accordance with the manufacturers guidelines to qualify for warranty replacement. Please be advised that warranty claims for these parts may take up to 4 weeks for processing, and customers must cover shipping.

Shipping Info

This Item Qualifies For Free Shipping!

When Will My Order Ship?

All orders are typically processed within 24 hours of receiving payment and are shipped from us same day if placed before our shipping cutoff time (Monday - Friday: 12PM, Saturday: 10AM, Sunday: No Shipping), orders placed after our cutoff time are shipped the next morning.

Do You Offer Express Shipping?

Yes! Please note the shipping times are based on business days, weekends and holidays do not count to the delivery date. Please see our expedited ship time schedules here.

How Does Free Shipping Work?

Most orders over $99 qualify for free shipping! Orders which ship for free are shipped with either USPS or UPS based on our discretion. If you are using a PO box, free shipping orders will always go USPS.

Do You Ship To Canada?

We ship to Canada! We estimate USPS to take 4-10 days once receiving your package from us. We do not offer expedited shipping of any kind to Canada. Please allow an extra 2-5 days for all shipments to Canada. Free shipping is not available to Canada.

Do You Ship To Alaska Or Hawaii?

We ship to both Alaska and Hawaii! We do not offer next day or two day shipping to Alaska or Hawaii. Free shipping is not available to Alaska or Hawaii.

Do You Ship Outside The US Or Canada?

Unfortunately, at this time we do not offer international shipping other than to Canada.

Shipping Time Estimations

For information on shipping time estimations, see the Shipping Information & Transit Times on the shipping page.

Learn More About Our Shipping Information

Customer Reviews

Based on 2 reviews
50%
(1)
50%
(1)
0%
(0)
0%
(0)
0%
(0)
A
Ann S.
Vista flame igniter

Very pleased with this item. It was eady to install and fired the pellet stove right up. Everything is working as promised. I am so pleased. I'll be shopping with you guys.

C
Corry S.
Enviro Flame Igniter for pre-2004

Igniter was received, it is a exact replacement item. Packaging was not the best. The 2-connector pins (probes) were severely bent. I had to straighten and align the both of them. All else was O.K. Tested the system after and igniter works as needed.

QUESTIONS & ANSWERS

If your question does not concern this specific product, use our contact form
Ask a Question

  • What is the length from the mounting flange to the front of the tube?

    Over all length: 6-1/2"
    Length from flange to end of ignitor tube going into burn out area: 2-9/16"

  • I have an ef2i ignitor that scores in from the front of the fire box - both were very difficult to access and both sheered off when removing. What’s the easiest way to access these screwed from the front of the stove and how to acess the back of the screws now to try and get the broken off pieces out ? It’s either a very poor design or I am missing something .......probably the ladder ..

    The igniter comes out from the front. Unfortunately, the screws that hold it in are sometimes corroded. They are Torx20 screws and will often strip out if penetrating oil or the wrong size Torx bit isn't used

Customer Reviews

Based on 2 reviews
50%
(1)
50%
(1)
0%
(0)
0%
(0)
0%
(0)
A
Ann S.
Vista flame igniter

Very pleased with this item. It was eady to install and fired the pellet stove right up. Everything is working as promised. I am so pleased. I'll be shopping with you guys.

C
Corry S.
Enviro Flame Igniter for pre-2004

Igniter was received, it is a exact replacement item. Packaging was not the best. The 2-connector pins (probes) were severely bent. I had to straighten and align the both of them. All else was O.K. Tested the system after and igniter works as needed.